![]() Apple’s Mac mini has an HDMI connector, and its small form factor makes it an excellent hub for digital media, in part because of this HDMI connector. This sends digital audio to the receiver, but you can also use it if you’re playing video from the computer. If your computer has an HDMI output, and you use an AV receiver, which has several HDMI inputs, you can connect the two with an HDMI cable.This cable can also transport video from devices, such as streaming boxes. Many receivers and amplifiers that have onboard DACs have a coaxial jack as well. This is essentially an RCA jack, but that sends digital data. Some computers have soundcards with a digital coaxial jack.You can get a mini Toslink to Toslink cable in lengths from 3 to 25 feet, and they’ve become surprisingly affordable. The advantage to Toslink is that the audio is very clean you won’t have any of that crackle you may get from the plug in the headphone jack if it’s not seated correctly, or if the jack is a bit old and corroded. You’ll only find this on receivers or amplifiers that contain an onboard DAC (digital-analog connector), because the optical audio is digital and needs to be converted. This assumes, of course, that your amplifier or receiver has a Toslink input. For computers that have a digital audio output (all current Macs offer this, but I’m not sure how prevalent it is on the Windows side), you can use a mini Toslink to Toslink cable.(With the notable exception of the iPhone 7.) Cables like this are available at many lengths, and you can add extension cables if you need something even longer. This method is inexpensive and simple to use, and the headphone jack can plug into any computer, and most any other device that can play music. All amplifiers and receivers have several pairs of RCA jacks, and you generally connect a computer to the AUX pair. The easiest method is to use a cable that has a 1/8″ headphone jack at one end, to connect to your computer, and a pair of RCA plugs at the other, to connect to your amplifier or receiver.Here’s a list of 10 ways you can connect your computer to a stereo. Here’s the back of my AV receiver, Yamaha’s RX-V679, with its plethora of connectors, including analog RCA, optical (Toslink), coaxial, HDMI, and Ethernet: You’ll want to do this if you have audio SACDs with surround sound, or if you also play movies from your computer to the stereo device.Īmplifiers and receivers have lots of connections, and the most complex – AV receivers – give you plenty of options, but less feature-rich devices offer fewer connectors. If you want to send multi-channel audio to your receiver or amplifier, then you must use a digital connector of some sort. Note that the first method is the only way of sending analog audio to a stereo device all the other methods below send digital audio. Each of these methods addresses a different type of setup, such as whether your amplifier or receiver has an onboard DAC, or whether you use a standalone DAC. Depending on what type of audio equipment you use, and how your system is set up, you may choose a different method. There are many ways you can send music from your computer to your stereo. But I suspect is more than you wanted to get into. It would take a hobby box, a switch and few solder connection to make it all work. ![]() You could run a single XLR to your amp, then split that into both an XLR and RCA wired exactly the way they say. So as you see, there is no real magic to what the jumper does. The shorting pin connects pins 1 and 3 and grounds the inverted input." These pins must be removed to connect either unit for balanced operation. These pins must remain in the XLR inputs if the units are to operate in the singleended mode. The KSA-150 and KSA-250 are shipped with shorting pins in the XLR inputs. Only one of these inputs should be connected to the preamplifier. The RCA connector is wired in parallel with pin 2, the non-inverted input. The pin assignments for the XLRS are: pin 1 = signal ground: pin 2 = non-inverting input: pin 3 = inverting input. The balanced inputs use 3-pin XLR connectors and single -ended inputs use RCA connectors. "The KSA-150 and KSA-250 have both balanced and single -ended inputs. I am not sure which Krell amp you have but this is from the instruction manual for one of them:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |